• ASTM A333 Grade 6 Pipe, A333 Seamless Pipe, ASTM A333 Gr6 Pipe,ASTM a333 gr6 steel pipe,ASTM A333 Grade 6 seamless pipe
  • Q345D Square Steel Pipe
  • U type finned tube


Location : home > News

Description of Boiler Tube Grades & Recommended Uses per the ASME Boiler & Pressure Code Section 1 SA178 & SA213 grades

Posted on 2020/12/01

Carbon steels show mild corrosion resistance and fair strength up to 1000F. However, their usage above 800F must take into account the susceptibility to graphitization. Graphitization has not been a significant problem in thicknesses encountered in boiler tubing. Use of heavy section pipe above 800F, however, is not recommended. The application of seamless and welded carbon steel tubing in boilers is restricted to a maximum temperature of 800F for rimmed and 1000F for killed steel by the ASME Boiler and Pressure Vessel Code, "Section I, Power Boilers." The Code does not list maximum allowable stresses beyond 1000F for carbon steels.Carbon-molybdenum steels
Carbon-moly steels exhibit higher creep strengths than plain carbon steels, and are widely used in high-temperature boiler service. These steels nominally contain 0.5% molybdenum. When exposed to temperatures above 850-900F for long periods of time, the carbon-moly steels are also prone to graphitization. Again, the phenomenon is section-size dependent, and using pipe of this grade above 850F is not recommended. The carbide phase is not stable, and will revert to graphite. The ASME Boiler and Pressure Vessel Code, "Section I," lists allowable stresses for carbon-moly steels up to 1000F.
This low alloy steel exhibits graphitization resistance and greater creep strength than the carbon-moly steels. Corrosion resistance is comparable to carbon-moly. T2 has allowable stresses listed up to 1000F in the ASME Boiler Code.

ASTM A213 T11 Boiler Tube

ASTM A213 T11 Boiler Tube
The chromium in all of the Croloys stabilizes the carbon as chromium carbides, thus making them immune to graphitization.
This is a 1-chromium, 1/2-molybdenum alloy which is limited to a maximum temperature of 1200F by the ASME Boiler and Pressure Vessel Code, "Section I, Allowable Stresses." T12 is sometimes used in place of T2 tubing because of its greater strength.
This grade has the same creep strength properties as T12. It is more corrosion resistant than the chromium-free steels, and is fairly resistant to high-temperature oxidation because of its higher silicon and chromium contents.
Oxidation resistance is important because metals exposed to elevated temperatures for extended periods of time will accumulate a protective coating of scale. At some minimum temperature, the scale will become non-adherent, gradually flake, and cause solid particle erosion of turbines. However, exfoliation rarely causes failures before creep or high temperature yielding.
Allowable stresses are listed by the ASME Boiler and Pressure Vessel Code to 1200F.
This 2-1/4 chromium, 1 molybdenum alloy has exceptionally high creep properties, but is limited for applications to 1125F because of possible higher temperature scale exfoliation. It is listed in the ASME Boiler Code for temperatures to 1200F.
A 9-chromium-1 molybdenum alloy, T9 offers very good corrosion resistance with good high-temperature strength. It also has good oxidation resistance and can be used to 1200F maximum. Some times T9 is an adequate substitute for the more expensive stainless grades. The Boiler Code limits T9 to 1200F.
STAINLESS STEELS – Austenitic stainless steels

SA213 Boiler Tube

SA213 Boiler Tube
Austenitic stainless steels are presented in the ASME Boiler and Pressure Vessel Code with two sets of allowable stresses. The reason for this is their relatively low yield strength. The higher allowable stress values were determined at temperatures where the usage would be restricted by the short-time tensile properties.
The higher stresses exceed 62-1/2%, but do not exceed 90% of the yield strength. At these stresses, small amounts of plastic deformation can be expected. These higher stress values are usually used for super-heater and reheater tubing.
The Boiler Code lists maximum allowable stresses for varying temperatures depending on the individual austenitic stainless grade.
Variations of this 18 chromium, 8 nickel grade include 304L, 304LN, 304H and 304N. Each of these offers excellent corrosion and oxidation resistance along with high strength.
High strengths are maintained in the low carbon grades by controlling the nitrogen content.
T304 has higher carbon and a minimum solution annealing temperature to assure good long-time elevated temperature strengths. T304 grades are limited to 1650F under oxidizing conditions. Section I of the ASME Boiler Code lists allowable stresses up to 1500F.
T316 is similar to T304, but offers better corrosion resistance and creep strength. The molybdenum addition to 316 increases its resistance to pitting and crevice corrosion.
Variations of this grade include 316L, 316LN, 316H and 316N.
and T347
T321 and 347 are variations of T304 and have comparable minimum tensile properties. These two grades are stabilized with additions of titanium and columbian respectively, along with proper hea

how to contact us?


Cangzhou Datang Steel Pipe Co., Ltd All Right Resevered.